Can I Install a Tub Myself? Considerations And Also Steps
Can I Install a Tub Myself? Considerations And Also Steps
Blog Article
We've found this article relating to Tools You Need to Install a New Bathtub listed below on the internet and thought it made good sense to share it with you on this page.
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably challenging project. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall surface to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the task and fit attempting it. Rather than employing a professional to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly help you set up a new tub in your bathroom if you have actually already gotten a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and material list ought to consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic because of the limited accessibility that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will certainly originate from the pipes. When the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using both wood boards under its feet, place the bathtub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as changing the feet on the bathtub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the very same for the other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bath paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been used at the very least once as this will resolve it into its last position.
Planning for the Setup
To start with, the sustaining frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to stop strain on the tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components as well as installations. They are marketed in tubes and also cartridges, and are capable of sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that article about Tools You Need to Install a New Bathtub while looking around the web. Are you aware of another individual who is involved in the niche? Why not promote it. We love reading our article about Tools You Need to Install a New Bathtub .
Automated Marketing
Report this page